Determination of caffeine in dietary supplements by miniaturized portable liquid chromatography.

In this study three miniaturized liquid chromatography (LC) instruments have been evaluated and compared for the analysis of caffeine in dietary supplements, namely a benchtop capillary LC (capLC) system, a benchtop nano LC (nanoLC)system and a portable LC system. Commercial products derived from different sources of caffeine have been analyzed. Under optimized conditions, the methods based on benchtop systems were superior in terms of sensitivity. The limits of detection (LODs) found with the capLC and nanoLC systems were 0.01 and 0.003 µg mL-1, respectively, whereas the LOD obtained with the portable LC instrument was of 1 µg mL-1. The portable LC-based method was superior in terms of simplicity and throughput (total analysis time < 15 min). On the basis of the results obtained, a new method for the rapid measurement of caffeine in dietary supplements by portable miniaturized LC is presented. This method provided good linearity within the 1-20 µg mL-1 interval, and it allowed the quantification of caffeine even in products derived from decaffeinated green coffee extracts. The contents of caffeine found with the proposed portable LC method in the real samples analyzed ranged from 1.38 to 7 mg per gram of product, which were values statistically equivalent to those found with the benchtop capLC and nanoLC methods, being the precision, expressed as relative standard deviation (RDS), of 2 -14% (n = 3). The proposed portable LC based method can be used as a simple and rapid alternative to estimate the quality, effectiveness and safety of dietary supplements, regarding their caffeine content.

Exploring hand-portable nano-liquid chromatography for in place water analysis: Determination of trimethylxanthines as a use case.

Analytical performance and optimization of figures of merit of a portable nano liquid chromatograph (NanoLC) with UV detection at 255 nm have been established for in place analysis. Methylxanthines: caffeine, theophylline and theobromine were selected as target analytes. A fast lab method based on IT-SPME coupled on line with capillary liquid chromatograph (CapLC) with diode array detection (DAD) was employed for comparative studies. IT-SPME and solid phase extraction were coupled off-line to NanoLC for improving instrumental parameters, mainly detection capacity and selectivity. IT-SPME or SPE/portable NanoLC based methods were superior in terms of chromatographic resolution and organic solvent consumption per sample, around 200 µL vs 10 mL for IT-SPME-CapLC-DAD. Limits of detection (LODs) obtained with the SPE/portable NanoLC were 2-10 ng/mL, which can be suitable for testing the presence of the analytes in several environmental waters in the field. As predictable, the lab method provided better LODs, between 0.1 and 0.5 ng/mL. Good linearity was achieved for both methods and precision was similar for them (≤7%). Both systems were tested for the analysis of real water samples with suitable results.

On-line in-tube solid phase microextraction coupled to capillary liquid chromatography-diode array detection for the analysis of caffeine and its metabolites in small amounts of biological samples.

In-tube solid phase microextraction (IT-SPME) coupled on-line to capillary liquid chromatography with diode array detection provides a simple and fast analytical methodology for the simultaneous quantitation of caffeine and its three primary metabolites (theobromine, paraxanthine and theophylline) in micro samples of serum, saliva and urine matrices. The sample amount required for one analysis was only 2.5 µL of saliva, 6.25 µL of serum or 40 µL of urine, a requirement for its implementation in a hospital laboratory for preterm newborns, where sample availability is a major problem. In standard conditions, 25 µL of diluted saliva or serum (or 100 µL of urine) were processed by IT-SPME in 30 cm of commercially available capillary GC column coated with ZB-FFAP (100% nitroterephthalic modified polyethylene glycol). The retained compounds were desorbed from the IT-SPME capillary by the mobile phase (a gradient mixture of water and methanol) and the separation was carried out in a C18 column (150 mm × 0.5 mm i.d., 5 µm particle size). Analytes eluted before 14 min, at a flow rate of 15 µL min-1, and were detected by absorbance at 275 nm. The calibration graphs presented good linearity (R2 > 0.99), without the presence of matrix effect, and recoveries between 84 and 112% were obtained. Limits of detection (S/N = 3) were 0.1 µg·mL-1 in serum and 0.5 µg·mL-1 in saliva and urine samples, for all compounds, and the intra- and inter-day variation coefficients (n = 3) were between 3 and 17%. Analytical figures of merit were similar to those proposed by other methodologies, but using lower sample volume and a faster and simpler sample treatment and analysis. Paired samples of serum and saliva from preterm newborns treated with caffeine at the pediatric intensive care unit were analyzed by the method, with statistically equivalent results for caffeine concentrations.

Quantitative Analysis of Terpenic Compounds in Microsamples of Resins by Capillary Liquid Chromatography.

A method has been developed for the separation and quantification of terpenic compounds typically used as markers in the chemical characterization of resins based on capillary liquid chromatography coupled to UV detection. The sample treatment, separation and detection conditions have been optimized in order to analyze compounds of different polarities and volatilities in a single chromatographic run. The monoterpene limonene and the triterpenes lupeol, lupenone, ß-amyrin, and α-amyrin have been selected as model compounds. The proposed method provides linear responses and precision (expressed as relative standard deviations) of 0.6% to 17%, within the 0.5-10.0 µg mL-1 concentration interval; the limits of detection (LODs) and quantification (LOQs) were 0.1-0.25 µg mL-1 and 0.4-0.8 µg mL-1, respectively. The method has been applied to the quantification of the target compounds in microsamples. The reliability of the proposed conditions has been tested by analyzing three resins, white copal, copal in tears, and ocote tree resin. Percentages of the triterpenes in the range 0.010% to 0.16% were measured using sample amounts of 10-15 mg, whereas the most abundant compound limonene (≥0.93%) could be determined using 1 mg portions of the resins. The proposed method can be considered complementary to existing protocols aimed at establishing the chemical fingerprint of these kinds of samples.

Establishing the occurrence and profile of polycyclic aromatic hydrocarbons in marine sediments: The eastern Mediterranean coast of Spain as a case study.

Sampling, cost-effective analysis, diagnosis of sources of pollution and assessment of potential toxicological effects were included in the case study. Marine sediments collected from 24 points along the eastern Mediterranean coast of Spain (Comunitat Valenciana region) in 2010, 2011, 2012 and 2015 have been analysed for polycyclic aromatic hydrocarbons. Fluoranthene, pyrene, chrysene, benzo[b]fluoranthene and benzo[a]pyrene were the most found. An analysis of the relative abundance of selected PAHs revealed that petrogenic and mixed petrogenic/pyrogenic sources are predominant in the area. The total concentrations of the target compounds ranged from 14.7 to 615.3 ng/g dry weight. The effects range-low (ERL) guideline values were used to assess potential toxicological effects. Rarely adverse biological effects can be expected in the tested area. The level of pollution by PAHs in the area can be considered low, although occasionally high values can be found, particularly in areas with high population or ship traffic.

A new tool for direct non-invasive evaluation of chlorophyll a content from diffuse reflectance measurements.

Chlorophyll is a key biochemical component that is responsible for photosynthesis and is an indicator of plant health. The effect of stressors can be determined by measuring the amount of chlorophyll a, which is the most abundant chlorophyll, in vegetation in general. Nowadays, invasive methods and vegetation indices are used for establishing chlorophyll amount or an approximation to this value, respectively. This paper demonstrates that H-point curve isolation method (HPCIM) is useful for isolating the signal of chlorophyll a from non-invasive diffuse reflectance measurements of leaves. Spinach plants have been chosen as an example. For applying the HPCIM only the registers of both, a standard and the sample are needed. The results obtained by HPCIM and the invasive method were statistically similar for spinach leaves: 144±6mg/m2 (n=5) and 155±40mg/m2 (n=5), respectively. However, more precise values were achieved with the HPCIM, which also involved minimal experimental effort. The HPCIM method was applied to spinach plants stressed by the action of several pesticides and water scarcity, showing a decrease of chlorophyll a content with time, which is related with a loss of health. The results obtained were compared with those achieved by two different reflectance vegetation indices (Macc01 and NDVI). Although NDVI and HPCIM gave similar footprints for the plants tested, vegetation indices fail in the estimation of real content of the chlorophyll a. The HPCIM could contribute to improve the knowledge of the chlorophyll a content of vegetation like health indicator, by applying it to a much employed non-invasive technique such as diffuse reflectance, which can be used in place or in remote sensing mode.

New optical paper sensor for in situ measurement of hydrogen sulphide in waters and atmospheres.

A novel and low-cost colorimetric sensor for the determination of hydrogen sulphide in environmental samples has been developed. This sensor is based on the immobilization of the reagent N,N-Dimethyl-p-phenylenediamine and FeCl3 in paper support, in which the H2S is adsorbed in order to give rise to the formation of methylene blue as reaction product. The sensor has been applied to determine H2S in water and air samples. Two different sampling systems for H2S caption from the air have been assayed: active and passive sampling. The analytical properties of the different systems have been obtained and compared. The analytical signals, corresponding to the methylene blue, have been obtained measuring the absorbance by conventional reflectance diffuse or using different algorithms for quantifying color intensity. The results obtained with both measurement procedures were comparable, with a detection limit of 1.11 and 1.12mLm(-3) for air samples (active and passive), and 0.5mgL(-1) for water samples. The developed sensor provides good accuracy and precision (RSD<12%) and simplifies significantly the analytical measurements because it avoids the need of preparing derivatization reagents, sample handling and allows in situ measurements. The reaction product obtained is highly stable in this support and no provide any blank signal. Under the optimal conditions, the proposed method exhibit excellent visual sensitivity for the naked eye procedure, making the detection of H2S possible.

Determination of amphetamines in hair by integrating sample disruption, clean-up and solid phase derivatization.

The utility of matrix solid phase dispersion (MSPD) for the direct analysis of amphetamines in hair samples has been evaluated, using liquid chromatography (LC) with fluorescence detection and precolumn derivatization. The proposed approach is based on the employment of MSPD for matrix disruption and clean-up, followed by the derivatization of the analytes onto the dispersant-sample blend. The fluorogenic reagent 9-fluorenylmethyl chloroformate (FMOC) has been used for derivatization. Different conditions for MSPD, analyte purification and solid phase derivatization have been tested, using amphetamine (AMP), methamphetamine (MET), ephedrine (EPE) and 3,4-methylenedioxymethamphetamine (MDMA) as model compounds. The results have been compared with those achieved by using ultrasound-assisted alkaline digestion and by MSPD combined with conventional solution derivatization. On the basis of the results obtained, a methodology is proposed for the analysis of amphetamines in hair which integrates sample disruption, clean-up and derivatization using a C18 phase. Improved sensitivity is achieved with respect to that obtained by the alkaline digestion or by the MSPD followed by solution derivatization methods. The method can be used for the quantification of the tested amphetamines within the 2.0-20.0ng/mg concentration interval, with limits of detection (LODs) of 0.25-0.75ng/mg. The methodology is very simple and rapid (the preparation of the sample takes less than 15min).

Selective and sentivive method based on capillary liquid chromatography with in-tube solid phase microextraction for determination of monochloramine in water.

Due to the difficulties of working with chloramines, a critical examination of monochloramine standard preparation has been performed in order to select the best synthesis conditions. The analyte has been determined by in-tube solid phase extraction coupled to capillary liquid chromatography with UV detection (IT-SPME Capillary LC DAD). Potential factors affecting the response of monochloramine such as the pH of mobile phase and the volume of sample processed by IT-SPME Capillary LC DAD have been investigated and optimized. According to the results of the study, 0.1 mL or 4.0 mL of sample at neutral pH were loaded in the chromatographic system. A sensitive and selective method has been developed for the determination of monochloramine in water. Validation of the method has been performed. The linear range was 0.09-5mg/L with linear regression coefficients (R(2)) greater than 0.995. Method reproducibility expressed as relative standard deviation (RSD, %), was lower than 15%. The limits of detection (LODs) were 0.029 and 0.01 mg/L by processing 0.100mL or 4 mL of the samples, respectively, being below the maximum residues levels allowed for this compound. The sensitivity achieved by the developed method was better than that obtained by the reference method. The developed method was applied to water samples (tap and swimming pool water).

Development of a polydimethylsiloxane-thymol/nitroprusside composite based sensor involving thymol derivatization for ammonium monitoring in water samples.

This report describes a polydimethylsiloxane (PDMS)-thymol/nitroprusside delivery composite sensor for direct monitoring of ammonium in environmental water samples. The sensor is based on a PDMS support that contains the Berthelot's reaction reagents. To prepare the PDMS-thymol/nitroprusside composite discs, thymol and nitroprusside have been encapsulated in the PDMS matrix, forming a reagent release support which significantly simplifies the analytical measurements, since it avoids the need to prepare derivatizing reagents and sample handling is reduced to the sampling step. When, the PDMS-thymol/nitroprusside composite was introduced in water samples spontaneous release of the chromophore and catalyst was produced, and the derivatization reaction took place to form the indothymol blue. Thus, qualitative analysis of NH4(+) could be carried out by visual inspection, but also, it can be quantified by measuring the absorbance at 690 nm. These portable devices provided good sensitivity (LOD<0.4 mg L(-1)) and reproducibility (RSD <10%) for the rapid detection of ammonium. The PDMS-NH4(+) sensor has been successfully applied to determine ammonium in water samples and in the aqueous extracts of particulate matter PM10 samples. Moreover, the reliability of the method for qualitative analysis has been demonstrated. Finally, the advantages of the PDMS-NH4(+) sensor have been examined by comparing some analytical and complementary characteristics with the properties of well-established ammonium determination methods.

A cost-effective method for estimating di(2-ethylhexyl)phthalate in coastal sediments.

This study describes the development of a new method for the analysis of di(2-ethylhexyl)phthalate (DEHP) using 0.1-0.3 g of sediment sample, based on matrix solid phase dispersion (MSPD) using C18 as dispersant phase (0.4 g) and acetonitrile-water as eluting solvent (3.4 mL 1:3.25, v/v). No evaporation step is required. 3 mL of extracts were processed on-line by in-tube solid phase microextraction (IT-SPME) coupled to capillary liquid chromatography (CapLC) and diode array detector (DAD). A short analytical column Zorbax SB C18 (35×0.5 mm, 5 µm) provided suitable results. FTIR-ATR was employed for characterizing sediment samples and MSPD procedure. The total analysis time was less than 20 min (MSPD takes about 10 min). The utility of the described approach has been tested by analyzing several real samples. No matrix effect was found. Achieved precision was less than 10% for DEHP estimation. Detection limits in samples were 270 and 90 µg/kg for 0.1 and 0.3 g of taken sediment, respectively.

In situ colorimetric quantification of silver cations in the presence of silver nanoparticles.

Silver ions (Ag(+)) can be quantified in situ in the presence of AgNPs by using a colorimetric sensing probe (3,3',5,5'-tetramethylbenzidine). Interestingly, it also enables detection of the Ag(+) adsorbed on the AgNP surface. This is relevant to design new methods to make AgNPs while ensuring the total reduction of Ag(+).

Study of the influence of temperature and precipitations on the levels of BTEX in natural waters.

Assessment of seasonal changes in surface water quality is an important aspect for evaluating temporal variation of water due to natural or anthropogenic inputs of point and non-point sources. The objective of this paper was to investigate the influence of seasonal temperature fluctuations and precipitations on the levels of BTEX in natural waters. Principal component analysis (PCA) was used to evaluate the seasonal correlations of BTEX levels in water and to extract the parameters that are most important in assessing seasonal variations of water quality. This study was carried out as a part of VOCs monitoring program in natural water samples from Mediterranean coast. To carry out this project, a multiresidue analytical method was used. The method was based on headspace solid-phase microextraction (HS-SPME) followed by gas chromatography coupled to flame ionization detector (FID). The limits of detection LODs found for the tested analyte tested were in the 0.001-1 µg/L range. These values were adequate for the analysis of these compounds in water samples according to the regulated values. Water samples from different points of the Mediterranean coast were analyzed during a period of three years, and were taken four times per year. Most of the compounds were below the limit established by the legislation. The results obtained by a chemometric study indicated that temperature and precipitations can be related on the BTEX levels found in water. A regression model between temperature or precipitations and BTEX concentration was obtained, thus these models can be used as predictive model for detection any non-normal concentration level.

More about sampling and estimation of mercaptans in air samples.

Several strategies have been developed for sampling and determination of volatile thiols. The selectivity and sensitivity of the proposed methodologies are achieved by using a specific derivatizing reagent. The different procedures assayed are based on air sampling followed by derivatization of the analytes with OPA and isoleucine in alkaline solution. The derivatization products are separated and determined by liquid chromatography and fluorescence detection. To start, the derivatization conditions and stability of the derivates have been studied in order to establish the storage conditions. In general, the strategies studied consisted on trapping and detivatization the thiol compound on different support; a solution (Impinger) or sorbent (C18 cartridges or glass fiber filter). The analytical properties of the different strategies have been obtained and compared. Procedures are recommended upon specific situations.

Cleaning sorbents used in matrix solid-phase dispersion with sonication: application to the estimation of polycyclic aromatic hydrocarbons at ng/g levels in marine sediments.

This study shows that ultrasonic assisted extraction is a good practise for removing impurities from sorbents used for matrix-solid phase dispersion (MSPD). A previous washing of the sorbent with an organic solvent or mixture of solvents eliminates part of the interferences, but this treatment is not enough for the quantification of PAHs at ng/g levels. It is demonstrated that the determination of traces of polycyclic aromatic hydrocarbons (PAHs) in solid samples processed by matrix-solid phase dispersion (MSPD) may be severely affected by the presence of sorbent impurities. Different extraction solvents and sonication conditions have been tested, and on the basis of the results obtained a new approach is presented for cleaning sorbents typically used in MSPD such C(18), silica or Florisil. The utility of the described approach has been illustrated by analysing by liquid chromatography and fluorescence detection different marine sediments.

Advantages of monolithic over particulate columns for multiresidue analysis of organic pollutants by in-tube solid-phase microextraction coupled to capillary liquid chromatography.

The performance of a monolithic C(18) column (150 mm×0.2 mm i.d.) for multiresidue organic pollutants analysis by in-tube solid-phase microextraction (IT-SPME)-capillary liquid chromatography has been studied, and the results have been compared with those obtained using a particulate C(18) column (150 mm×0.5 mm i.d., 5 µm). Chromatographic separation has been carried out under isocratic elution conditions, and for detection and identification of the analytes a UV-diode array detector has been employed. Several compounds of different chemical structure and hydrophobicity have been used as model compounds: simazine, atrazine and terbutylazine (triazines), chlorfenvinphos and chlorpyrifos (organophosphorous), diuron and isoproturon (phenylureas), trifluralin (dinitroaniline) and di(2-ethylhexyl)phthalate. The results obtained revealed that the monolithic column was clearly advantageous in the context of multiresidue organic pollutants analysis for a number of reasons: (i) the selectivity was considerably improved, which is of particular interest for the most polar compounds triazines and phenyl ureas that could not be resolved in the particulate column, (ii) the sensitivity was enhanced, and (iii) the time required for the chromatographic separation was substantially shortened. In this study it is also proved that the mobile-phase flow rates used for separation in the capillary monolithic column are compatible with the in-valve IT-SPME methodology using extractive capillaries of dimensions similar to those used in conventional scale liquid chromatography (LC). On the basis of these results a new method is presented for the assessment of pollutants in waters, which permits the characterization of whole samples (4 mL) in less than 30 min, with limits of detection in the range of 5-50 ng/L.

In-tube solid-phase microextraction coupled by in valve mode to capillary LC-DAD: Improving detectability to multiresidue organic pollutants analysis in several whole waters.

A simple and fast capillary chromatographic method has been developed to identify and quantify organic pollutants at sub-ppb levels in real water samples. The major groups of pesticides (organic halogens, organic phosphorous, and organic nitrogen compounds), some hydrocarbons (polycyclic aromatic hydrocarbons), phthalates and some phenols such as phenol and bisphenol A (endocrine disruptors) were included in this study. The procedure was based on coupling, in-tube solid-phase microextraction (IT-SPME) by using a conventional GC capillary column (95% methyl-5% phenyl substituted backbone, 80cmx0.32mm i.d., 3microm film thickness) in the injection valve to capillary liquid chromatography with diode array detection. A comparative study between the IT-SPME manifold and a column-switching device using a C(18) column (35mmx0.5mm i.d., 5microm particle size) has been performed. The IT-SPME procedure was optimal, it allows reaching limits of detection (LODs) between 0.008 and 0.2microg/L. No matrix effect was found and recoveries between 70 and 116% were obtained. The precision of the method was good, and the achieved intra- and inter-day variation coefficients were between 2 and 30%. This procedure has been applied to the screening analysis of 28 compounds in whole waters from several points of the Mediterranean coast (Valencia Community, Spain).

On-line determination of aliphatic amines in water using in-tube solid-phase microextraction-assisted derivatisation in in-valve mode for processing large sample volumes in LC.

This paper describes a cost-effective procedure for the analysis of short-chain aliphatic amines in water samples using a solid-phase microextraction device. Analyte preconcentration and derivatisation were effected into a capillary column coated with 95% polydimethylsiloxane-5% polydiphenylsiloxane, which was used as the injection loop of a Rheodyne injection valve. The coating was previously loaded with the derivatisation reagent, 9-fluorenylmethyl chloroformate. A volume of 1 mL of samples was then drawn into the capillary column, and the extracted analytes were left to react on the capillary coating for 5 min. Next, the capillary column was cleaned by passing water. Finally, the injection valve was rotated, and the derivatives formed were dynamically desorbed and transferred to the analytical column into the mobile phase. Methylamine, ethylamine, propylamine, n-butylamine and n-pentylamine were selected as model compounds. Excellent sensitivity was achieved, being the limits of detection of 15-200 microg/L when using UV detection and of 0.1-0.4 microg/L by fluorescence.

New micromethod combining miniaturized matrix solid-phase dispersion and in-tube in-valve solid-phase microextraction for estimating polycyclic aromatic hydrocarbons in bivalves.

Miniaturized matrix solid-phase dispersion (MSPD) was developed for the extraction of common polycyclic aromatic hydrocarbons (PAHs) from bivalve samples (100mg, dry weight). Additional clean-up and analyte enrichment was accomplished by in-tube solid-phase microextraction (SPME). For this purpose the extracts collected after MSPD were diluted with water and injected into a capillary column coated with the extractive phase. This capillary column was connected to the analytical column by means of a switching valve. Separation and quantification of the PAHs were carried out using a monolithic LC column and fluorescence detection. Since the in-tube SPME device allowed the processing of large volumes of the extracts (2.0 mL) excellent sensitivity was achieved, thus making solvent evaporation operations unnecessary. The overall recoveries ranged from 10% to 28% for the studied compounds. The relative standard deviation (RSD) ranged from 2% to 10% for intra-day variation (n=3), and the limits of detection (LODs) were < or =0.6 ng/g (dry weight). The proposed procedure was very simple and rapid (total analysis time was approximately 20 min), and the consumption of organic solvents and extractive phases was drastically reduced. The reliability of the proposed MSPD/in-tube SPME method was tested by analysing several bivalves (mussels and tellins) as well as a standard reference material (SRM).

Chemiluminescent method for detection of eutrophication sources by estimation of organic amino nitrogen and ammonium in water.

An automatic method has been developed for the estimation of organic amino nitrogen (CH2-NH) and ammonium in water samples. We propose a continuous flow system in which nitrogen compounds react with hypochlorite reagent to produce chloramines. Subsequently, the mixture is mixed with luminol, generating a chemiluminescence signal. The signal emission at 425 nm, registered as a function of time, decreases as nitrogen concentration increases, due to the decrease on hypochlorite concentration. A large number of nitrogen compounds have been assayed and their sensitivities compared, in milligrams per liter nitrogen. The ammonium calibration graph, expressed as N, can be used for most of the assayed compounds. The linear interval was 0.24-4 mg L(-1) N, with the detection limit 0.07 mg L(-1) N. The chemiluminescence method was applied to the analysis of several kinds of real water samples, natural, lake, irrigation ditch, fountain, residual, and seawater in order to detect possible sources of eutrophication. The accuracy (% relative error) and precision were satisfactory, with mean values of 5 +/- 4 and 3 +/- 2, respectively. This procedure has been used to estimate nitrogen content in samples before and after Kjeldahl treatment. In the same samples, the N found for the untreated samples provided a good estimation of the N Kjeldahl. Sixty samples per hour can be analyzed, and the procedure can also be used for in situ monitoring.